一区二区av在线_国产在视频一区二区三区吞精_国产精品一区视频_中文字幕日韩一区二区不卡_www.毛片_欧美视频一区

The two-component gluing machine is divided into automatic, semi-automatic and fully automatic. Many customers do not understand how to start the machine and how to operate it. Next, I will tell you how to do it.

首要要了解為什么要運用雙組份打膠機來工作

First of all, we should understand why we should use the two-component glue machine to work

設備運用的重要性：中空玻璃在制作過程中，有一個環節是非常關鍵的，便是用結構膠將兩片玻玻璃徹底密封，因?yàn)槿斯ご蚰z慢，關閉不好，所以大量的出產中空玻璃就需要設備。

The importance of equipment application: in the production process of insulating glass, there is a key link, that is, to seal the two pieces of glass completely with structural adhesive. Because manual gluing is slow and the closing is not good, it is necessary to produce a large number of insulating glass with equipment.

雙組份打膠機的操作方法：

Operation method of two-component gluing machine:

1、首要打開氣泵開關，電源總開關，控制臺開關，在控制臺按手動按鈕

1. First turn on the air pump switch, the main power switch, the console switch, and press the manual button in the console

2、然后在雙組份打膠機的顯現屏上找到原點設定，點擊輔助原點設定，然后點擊頭部原點設定

2. Then find the origin setting on the display screen of the two-component gluing machine, click the auxiliary origin setting, and then click the head origin setting

3、注意原點設定時避免頭部和輔助吸盤碰撞。等設定好然后回來找到玻璃厚度設定

3. Pay attention to avoid collision between the head and the auxiliary suction cup when setting the origin. Wait until it's set and come back to find the glass thickness setting

4、先是玻璃的厚度然后是鋁隔條然后還是玻璃的厚度

4. First the thickness of the glass, then the aluminum spacer, and then the thickness of the glass

5、輸入完以后，點擊設置進入。等指令方位和當前方位數值共同即可，注意設置時傳送帶上不要有玻璃。

5. After input, click settings to enter. It is OK to wait for the command orientation and the current orientation value to be common. Note that there is no glass on the conveyor belt when setting.

雙組份打膠機操作時狀況剖析：

Analysis of the operation condition of the two-component glue applicator

1、雙組份打膠機開始打膠要看每條邊每個角打膠是否均勻

1. When the two-component gluing machine starts to apply glue, it depends on whether the glue is evenly applied at each edge and corner

2、在屏幕上點擊回來找到密封配方，點擊進入，會顯現當前密封壓力

2. Click back on the screen to find the sealing formula. Click enter to display the current sealing pressure

3、如果每條邊都缺膠，那么可增加壓力，壓力大膠量大，壓力小膠量就小。

3. If each side is short of glue, then the pressure can be increased. If the pressure is large, the glue quantity is small when the pressure is small.