雙組份打膠機的結構原理簡單好理解
雙組份打膠機由A、B膠泵、氣動系統、升降機構、機架等組成?，F分別介紹如下：
The two-component glue applicator is composed of a and B glue pumps, pneumatic system, lifting mechanism and frame. The introduction is as follows:
1.膠泵：
1. Rubber pump:
（1）A、B組份各設一個膠泵，在各自的氣馬達驅動下，分別作往復運動，將膠吸入并壓出。A、B膠泵分別與壓膠盤固定在一起，再與機架連接組成各自的系統。
(1) Components a and B are each provided with a rubber pump, which reciprocates under the driving of their respective air motors to suck and press out the rubber. A. The glue pump B is fixed with the glue pressing plate, and then connected with the rack to form their own systems.
（2）A、B組份的配比是通過比例杠桿進行調節：向里調節，B出膠量減少，向外調節，B出膠量增加。通過調節比例杠桿來控制B膠的出膠量，從而控制A、B膠的配比。
(2) The proportioning of components a and B is adjusted by a proportional lever: adjust inward, the glue output of B decreases, and adjust outward, the glue output of B increases. Adjust the proportional lever to control the glue output of glue B, so as to control the proportion of glue a and B.
（3）出膠量：由氣源處理器控制，逆時針調節，出膠量增加，順時針調節出膠量減小。（這里指總出膠量）本膠泵通過比例杠桿調節A、B膠量配比，具有操作靈活，性能穩定，調節范圍大等特點。
(3) Glue output: controlled by the air source processor, the glue output increases when it is adjusted counterclockwise, and decreases when it is adjusted clockwise. (here refers to the total glue output) the glue pump adjusts the proportion of glue a and B through the proportional lever, which has the characteristics of flexible operation, stable performance and large adjustment range.
2.升降機構：
2. Lifting mechanism:
A、B組份膠泵分別設一套氣動升降機構，該升降機構分別由兩個氣缸并聯組成，并通過橫梁固定連接各自的泵體。其目的之一是將兩缸的作用力通過壓盤作用在膠面上，壓力大小由調壓閥調節，一般調整在0.3MPa左右；
A. The component B rubber pump is provided with a set of pneumatic lifting mechanism, which is composed of two cylinders in parallel and is fixedly connected to the pump body through the beam. One of its purposes is to act the force of the two cylinders on the rubber surface through the pressure plate. The pressure is adjusted by the pressure regulating valve, generally about 0.3MPa;
其二，當需要更換膠桶時，氣缸可將壓盤提起。離開膠桶，以便更變新的膠桶。
Second, when the rubber barrel needs to be replaced, the cylinder can lift the pressure plate. Leave the rubber bucket for a new one.
The operation method of the two-component gluing machine is simple and flexible, and it has quickly occupied various industries suitable for gluing. If you have any needs or questions, please come to our website http://m.e846lbsv.cn Consult.
上一篇：正確理解打膠時出現“花膠”的情況
下一篇：淺談丁基膠打膠機阻塞的原因
